E30 series BMW 3

since 1983-1994 of release

Repair and car operation



E30 BMW
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engine
   - 3.1.2. Specifications
      3.1.3. Types of the repair work which is carried out without dismantle of the engine
      3.1.4. An order of installation of the piston of the 1st cylinder in VMT of a step of compression
      3.1.5. Cover of a head of cylinders
      3.1.6. A soaking-up collector
      3.1.7. Final collector
      3.1.8. Covers of a chain of a drive of a cam-shaft (M10 engine)
      3.1.9. Chain and asterisks (M10 engine)
      3.1.10. Covers of a gear belt (engines M20 and М40)
      3.1.11. Gear belt and cam-shaft asterisks (engines M20 and М40)
      3.1.12. Forward epiploons
      3.1.13. Head of cylinders
      3.1.14. Pallet
      3.1.15. Oil pump
      3.1.16. Flywheel (a leading disk)
      3.1.17. Back epiploon of the crankshaft
      3.1.18. Engine mount details
   + 3.2. Dismantle and major maintenance of the engine
   + 3.3. Engine electric equipment
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Transmissions
+ 9. Coupling
+ 10. Brake system
+ 11. Running gear
+ 12. Body
+ 13. Electric equipment
+ 14. Good advice


4d3121b2





3.1.12. Forward epiploons

Replacement

PERFORMANCE ORDER
M10 engine, cam-shaft epiploon
1. Remove the top cover of a chain.
2. Beat out an epiploon from the interior of a cover, having put a cover on wooden whetstones.
3. Grease and press a new epiploon in blows on the opravka of suitable diameter resting against an external part of an epiploon.
4. Further assembly is carried out upside-down.
M10 engine, crankshaft epiploon
5. Remove a pulley and an uspokoitel.
6. Accurately hook an epiploon a screw-driver wrapped up by an adhesive tape and get.
7. Clear an opening under an epiploon, grease and press a new epiploon in blows on the opravka of suitable diameter resting against an external part of an epiploon.
8. Further assembly is carried out upside-down.
Engines M20 and М40, cam-shaft epiploon
9. Remove a belt and a cam-shaft asterisk.
10. On the M20 engine get the epiploon case from a head of cylinders, having unscrewed 2 screws and turning the case in both parties.
11. On the M20 engine carefully beat out an epiploon from the interior of the case, having put the case on wooden whetstones.
12. On the M40 engine accurately hook an epiploon a screw-driver wrapped up by an adhesive tape and get from a head of cylinders.
13. Grease working edges and an external surface of a new epiploon with universal greasing.
14. On the M40 engine wrap up a shaft neck an adhesive tape and dress an epiploon.
15. Press a new epiploon in blows on the opravka of suitable diameter resting against an external part of an epiploon.
16. On the M20 engine replace a sealant of the case of an epiploon and establish the case, tighten screws.
17. Further assembly is carried out upside-down.
M20 engine, epiploons of the crankshaft and intermediate shaft
18. Remove a gear belt, pulleys of the crankshaft and an intermediate shaft.
19. Remove a forward cover, having unscrewed bolts (including 3 bottom bolts with which the pallet fastens) and having opened consolidation by blows of a rubber hammer, accurately clear of the remains of consolidation and beat out an epiploon from the interior of a cover, having put a cover on wooden whetstones.
20. Grease and press a new epiploon in blows on the opravka of suitable diameter resting against an external part of an epiploon.
21. Establish a cover, having replaced laying and having put RTV hermetic on condensed places and a cover joint with the pallet and the block of cylinders.
22. Further assembly is carried out upside-down.
M40 engine, forward epiploon of the crankshaft
23. Remove a gear belt and an asterisk.
24. Remove from the crankshaft a segment shponka.
25. Accurately hook an epiploon a screw-driver wrapped up by an adhesive tape and get. If the epiploon does not give in to removal, drill openings both screw screws-samorezy and get an epiploon for heads of screws.
26. Clear an opening under an epiploon, grease and press a new epiploon without distortions in blows on the opravka of suitable diameter resting against an external part of an epiploon.
27. Further assembly is carried out upside-down. Replace a gear belt.